Page - 1 - 2 - 3 -


AN/PAS-4 Infrared Weaponsight
(Polan Model P-155 / Varo Model 9903)
6914 IR Tube
Infrared image converter tube used in many earlier night vision units. Such as the Navy AN/SAR-7 Infrared Viewer, the Army M-18 Infrared Binoculars, Polan Model P-155 and Varo Model 9903 (AN/PAS-4) Infrared Weaponsights and various night vision elbow assemblies and periscopes. Also used in some commercial IR viewers.
Good Condition
$250.00
16KV Power Supply (Varo Model 3065 / M-18 Binocular Varo Model 3099)
A unitized, sealed, and very rugged unit originally used to power the 6914 IR tube. Requires 1.5 VDC input.
New Condition
$75.00
Eyepiece Assembly
The eyepiece assembly including the rear retaining nut. Rubber eyeguard is not included.
Good Condition
$35.00
Objective Lens Assembly
Front lens assembly requires spanner wrench to thread in place and focus.
Good Condition
$50.00



AN/PAS-6 Infrared Viewer (Metascope)
6929 IR Tube
Infrared image converter tube used mainly in the AN/PAS-6 Infrared Viewer and in some commercial IR viewers.
Good Condition
$250.00
12 KV Power Supply (Varo Model 3093A)
A unitized, sealed, and very rugged unit originally used to power the 6929 IR tube. Requires 1.5 VDC input.
New Condition
$75.00



AN/PVS-2 / 2A / 2B First Generation Night Vision Weaponsight (25mm)
Boresight Mount Assembly
An externally adjustable mount assembly that attaches to the STANAG spacing on the bottom of the unit.
This mount uses two knobs to zero the night vision weaponsight in 1/4 minute increments externally on the mount assembly.
Good Condition
$75.00
M-16 Adapter Bracket
This 'S' shaped bracket interfaces the PVS-2 attached boresight mount assembly to the AR-15/M-16 rifle. It clamps under the handle.
New Condition
$110.00
M-14 Adapter Bracket
This side mounted bracket interfaces the PVS-2 attached boresight mount assembly to the M1A/M-14 rifle.
Good Condition
$75.00
M-72 Adapter Bracket
This hinged bracket interfaces the PVS-2 to the M-72 L.A.W.S. rocket launcher. It clamps over the launcher and locks into place.
Good Condition w/carrying case
$225.00
M-79 Adapter Bracket
This side-adjustable bracket interfaces the PVS-2 to the M-79 gernade launcher. It clamps to the left side.
Good Condition
$175.00
High Voltage Oscillator
This electronic assembly produces the high frequency high voltage necessary. It plugs into the tube in the oscillator compartment under the cap.
New Condition
$75.00
Hight Voltage Oscillator Contact Cap
This circular assembly sits on top of the high voltage oscillator (above) to provide contact with the switch circuit.
Good Condition
$25.00
ABC Continuity Assembly (Red)
This oscillator shaped assembly takes the place of the oscillator on those tubes that have ABC (Automatic Brightness Control).
Good Condition
$25.00
Objective Lens Assembly
This is the 95mm diameter front lens.
Good Condition
$150.00
Eyepiece Assembly w/Lock Nut
This is the rear eyepiece assembly with the locknut that holds it into the rear of the scope.
Good Condition
$125.00
Rubber Eyeguard
This the rubber shuttered eyeguard that threads onto the rear eyepiece.
New Condition
$45.00
Battery and HV Oscillator Caps With Spring
Each unit requires two. One for the battery compartment and one for the oscillator comartment. Each cap also includes the necessary contact spring which slides into the bottom of each cap.
Good Condition
$25.00
3-Stage 25mm Image Intensifier Assembly for Rebuilding (Not
Working-Sold As Is)

These are the tubes for the AN/PVS-2 and AN/TVS-2 units. They are sold for parts and used by tube builders for reconditioning. Each contains (3) 25mm first generation image intensifier stages and one 45 KV power supply whic powers all three stages when assembled together.
Not working-sold as is
$75.00

Page - 1 - 2 - 3 -

Export Statementd